Every frame on the bus.
Decoded, on your Mac.
Watch CAN traffic in real time, decode it with your own DBC, run OBD-II diagnostics and transmit frames. The PEAK and Kvaser libraries ship inside the app, so there is nothing to install and nothing to configure.
- Version
- 1.0.0
- Platform
- macOS · macOS 14 or later · Apple silicon and Intel
- Interface
- Requires a supported PEAK or Kvaser USB interface.
| # | Time | ID | Name | Type | DLC | Data |
|---|---|---|---|---|---|---|
| 1041 | 12.084 210 | 0C0 | EngineData | Rx | 8 | 1A2F00640BC20010 |
| 1042 | 12.086 940 | 1A0 | WheelSpeeds | Rx | 8 | 07D007CE07D207CF |
| 1043 | 12.089 115 | 2F0 | SteeringAngle | Rx | 4 | FF3B0002 |
| 1044 | 12.091 002 | 7DF | OBD Request | Tx | 8 | 02010C5555555555 |
| 1045 | 12.093 480 | 7E8 | OBD Response | Rx | 8 | 04410C0BC2000000 |
| 1046 | 12.096 774 | 18FEF100 | CCVS1 | TP | 8 | FFFF1C20FFFFFFFF |
| 1047 | 12.099 301 | 3D2 | BrakeStatus | Rx | 2 | 0001 |
| 1048 | 12.101 668 | 0C0 | EngineData | Rx | 8 | 1A2F00660BC40010 |
The same traffic, read three ways
Switch in the toolbar. Every frame in arrival order, one row per identifier, or the signals a DBC decodes out of them.
| # | Time | ID | Name | Type | DLC | Data | ASCII |
|---|---|---|---|---|---|---|---|
| 1041 | 12.084 210 | 0C0 | EngineData | Rx | 8 | 1A2F00640BC20010 | ./.d.... |
| 1042 | 12.086 940 | 1A0 | WheelSpeeds | Rx | 8 | 07D007CE07D207CF | ........ |
| 1043 | 12.089 115 | 2F0 | SteeringAngle | Rx | 4 | FF3B0002 | .;.. |
| 1044 | 12.091 002 | 7DF | OBD Request | Tx | 8 | 02010C5555555555 | ...UUUUU |
| 1045 | 12.093 480 | 7E8 | OBD Response | Rx | 8 | 04410C0BC2000000 | .A...... |
| 1046 | 12.096 774 | 18FEF100 | CCVS1 | TP | 8 | FFFF1C20FFFFFFFF | ... .... |
| 1047 | 12.099 301 | 3D2 | BrakeStatus | Rx | 2 | 0001 | .. |
| 1048 | 12.101 668 | 0C0 | EngineData | Rx | 8 | 1A2F00660BC40010 | ./.f.... |
Every frame, in arrival order. Number, timestamp, identifier, type, DLC, hex payload and ASCII. It follows new frames automatically until you scroll away, and freezes on demand while the counters keep running.
Payload bytes that changed on the latest update are tinted, which makes it obvious which part of a message a node is actually moving.
Your own database, live
Open a Vector .dbc to name identifiers and turn payload bits into real values with units.
- The Signals view is a live table of those values, and any signal can be charted over time.
- Load several databases at once; collisions between them are listed rather than quietly resolved.
- Out-of-range values can be hidden, so a mis-scaled signal does not masquerade as data.
- Build a frame to transmit by editing signal values instead of counting bits.
Diagnostics on 11-bit CAN
SAE J1979 Mode 01: pick the PIDs you care about, poll them on an interval, or request one at a time.
| 0C | Engine RPM | 3 010.0rpm |
| 0D | Vehicle speed | 100km/h |
| 05 | Coolant temperature | 88°C |
| 11 | Throttle position | 24.7% |
| 0F | Intake air temperature | 31°C |
| 42 | Control module voltage | 14.1V |
- Read stored, pending and permanent trouble codes, and the vehicle's VIN.
- PID names, scaling and units come from a bundled OBD database.
- Requests go to 0x7DF, or to a single ECU at 0x7E0 for the vehicles that only answer one of them.
Send frames, and sequences of them
Identifier, flags and hex bytes, with cyclic send and a history of everything sent.
- Build the frame from a loaded DBC by editing signal values instead of counting bits.
- Multi-step sequences can be assembled and run.
- Right-click any captured frame to load it straight into the transmit panel.
Built for networks already running
CAN Classic and CAN FD, from 5 kbit/s to 1 Mbit/s, with an adjustable sample point.
- Bit rate
- 500 kbit/s
- Sample point
- 87.5 %
- Frame rate
- 1 204 f/s
- TEC / REC
- 0 / 0
- Listen-only mode: the controller never acknowledges, which is the safe way onto a live network.
- Automatic bit-rate detection, for when you do not know what you are plugged into.
- ISO-TP and J1939 reassembly, with PGN columns and flow control.
- Error and status frames carrying TEC and REC, with live bus load, frame rate and controller health.
Take the capture with you
CSV in four layouts, PEAK TRC and Vector ASC, including logging a session as it runs.
Export formats
- Raw, decoded, per-identifier summary, or CANedge.
- Import a CSV trace back in to work on a capture away from the hardware.
- Save and reopen an entire session: connection settings, filters, DBC files and transmit list.
Supported interfaces
The PEAK and Kvaser libraries ship inside the app bundle. There is no installer, no kernel extension and no system change.
- Both channels of a two-channel interface can run at once, in separate windows.
- USB interfaces only. There is no support for PCI, PC Card or LAN hardware.
Twenty-one languages
The whole interface, from the trace table to the transmit composer, follows the language of your Mac.
- English
- French
- Spanish
- German
- Italian
- Dutch
- Swedish
- Polish
- Czech
- Hungarian
- Portuguese
- Romanian
- Greek
- Turkish
- Russian
- Ukrainian
- Hindi
- Japanese
- Korean
- Chinese (Simplified)
- Chinese (Traditional)
What the app does not do
- No network connections
- CANcoyot makes none at all. No account, no telemetry, no analytics and no crash reporting service.
- Your capture stays put
- Traces, DBC files and diagnostic data stay on your Mac, and are written to disk only where you ask.
- Nothing to install
- Everything it needs is inside the app bundle. Copies in /usr/local/lib or Homebrew are never searched.
Plug in and watch
A native Mac app for the bus in front of you.
Version 1.0.0 · macOS 14 or later · Apple silicon and Intel
CANcoyot requires a supported USB CAN interface; it cannot capture anything without one. It is not affiliated with, endorsed by or sponsored by PEAK-System Technik GmbH, Kvaser AB or any vehicle manufacturer. Product names are trademarks of their respective owners and are used only to describe hardware compatibility.